“[50 Pack] Simpson Strong-Tie THDC25200H6SS Titen HD 1/4 in. x 2 in. Type 316 Stainless-Steel Heavy-Duty Screw Anchor” has been added to your cart.
View cart
Showing 1–40 of 42 resultsSorted by popularity
$ 279.64
Features
21 Gauge Steel Tie Wire
Bare steel with no coating
For use with MAX RB397, RB398, RB517 and RB518
$ 0.43
Features:
Faster installation than previous drop-in anchor design sets with 40% fewer hammer hits
Positive-set marking system indicates when anchor is properly set
Zinc-plated carbon steel
Length: 2 in.
Drill bit diameter: 5/8 in.
Minimum order quantity: 50
Order in multiples of: 50
$ 61.84
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes, hole size same as anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
Countersunk head allows screw anchor applications incompatible with a hex head
Available in 1/4″ and 3/8″ diameters
$ 95.38
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 629.50
Features
21 Gauge Steel Tie Wire
Bare steel with no coating
For use with MAX RB397, RB398, RB517 and RB518
$ 532.99
Features
Breathable polyester mesh
2″ two-tone tape for optimum visibility
Zipper closure
2 mic tabs with reinforced stitching
2 lower external flap pockets
$ 532.99
Features
Solid front and mesh back for breathability
2″ two-tone tape for optimum visibility
Zipper closure
2 mic tabs with reinforced stitching
2 lower external flap pockets
$ 28.49
Features
STB2-37334 has a chamfered top designed to prevent mushrooming during installation
Qualified for static and seismic loading conditions (seismic design categories A through F)
Suitable for horizontal, vertical and overhead applications
Qualified for minimum concrete thickness of 3 1/4″, and lightweight concrete-over-steel deck thickness of 2 1/2″ and 3 1/4″
Standard (ANSI) fractional sizes: fits standard fixtures and installs with common drill bit and tool sizes
$ 235.69
Features
Quick and easy installation
3PB is made of durable noncorrosive plastic
No tools required
$ 249.89
Features
Quick and easy installation
3BB is made of durable noncorrosive plastic
No tools required
$ 242.39
Features
Quick and easy installation
4-2IN-UBC is made of durable noncorrosive plastic
Snaps over the rebar
$ 45.58
Features
Consistent performance in high and low strength concrete
Nominal drill bit size is the same as the anchor diameter
Anchor can be installed through standard fixture holes
Length ID code and identifying marking stamped on head of each anchor
Anchor design allows for follow-up expansion after setting under tensile loading
$ 17.29
Features
Consistent performance in high and low strength concrete
Nominal drill bit size is the same as the anchor diameter
Anchor can be installed through standard fixture holes
Length ID code and identifying marking stamped on head of each anchor
Anchor design allows for follow-up expansion after setting under tensile loading
SALE 6% OFF
$ 106.92 Original price was: $106.92. $ 100.50Current price is: $100.50.
Features
THD37600H is tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes
Do not reuse anchor
$ 56.28
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes, hole size same as anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
Countersunk head allows screw anchor applications incompatible with a hex head
Available in 1/4″ and 3/8″ diameters
$ 179.09
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 62.17
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes, hole size same as anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
Countersunk head allows screw anchor applications incompatible with a hex head
Available in 1/4″ and 3/8″ diameters
$ 374.62
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 40.62
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 53.42
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes, hole size same as anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
Countersunk head allows screw anchor applications incompatible with a hex head
Available in 1/4″ and 3/8″ diameters
$ 45.77
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 188.46
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 93.08
Features
Thread design undercuts to efficiently transfer the load to the base material
Serrated cutting teeth and thread design enable quick and easy installation
Specialized heat-treating process creates tip hardness to facilitate cutting while the anchor body remains ductile
Designed to install using a rotary hammer or hammer drill with standard ANSI drill bits — no special tools required
Installs with standard-sized sockets
Code listed for cracked and uncracked concrete applications under the 2015, 2012 and 2009 IBC/IRC, per ICC-ES ESR-2713
FM listed
$ 316.92
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 346.15
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 190.14
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 288.46
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 166.15
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 223.08
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 59.69
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
SALE 20% OFF
$ 183.25 Original price was: $183.25. $ 146.60Current price is: $146.60.
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 72.26
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes, hole size same as anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
Countersunk head allows screw anchor applications incompatible with a hex head
Available in 1/4″ and 3/8″ diameters
$ 62.38
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
SALE 6% OFF
$ 64.92 Original price was: $64.92. $ 61.02Current price is: $61.02.
Features
Thread design undercuts to efficiently transfer the load to the base material
Serrated cutting teeth and thread design enable quick and easy installation
Specialized heat-treating process creates tip hardness to facilitate cutting while the anchor body remains ductile
Designed to install using a rotary hammer or hammer drill with standard ANSI drill bits — no special tools required
Installs with standard-sized sockets
Code listed for cracked and uncracked concrete applications under the 2015, 2012 and 2009 IBC/IRC, per ICC-ES ESR-2713
FM listed
$ 42.54
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 288.46
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 45.08
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 72.85
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 90.00
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 879.40
TW898 S Max 21ga Stainless Steel Tie Wire for MAX RB398 series