“[50 Pack] Simpson Strong-Tie THD37500H Titen HD 3/8 in. x 5 in. Heavy-Duty Screw Anchor” has been added to your cart.
View cart
Showing 1–40 of 42 resultsSorted by popularity
-
Delivery Estimate May 09 - May 13
$279.64
Features
- 21 Gauge Steel Tie Wire
- Bare steel with no coating
- For use with MAX RB397, RB398, RB517 and RB518
-
Delivery Estimate May 09 - May 13
$0.43
Features:
- Faster installation than previous drop-in anchor design sets with 40% fewer hammer hits
- Positive-set marking system indicates when anchor is properly set
- Zinc-plated carbon steel
- Length: 2 in.
- Drill bit diameter: 5/8 in.
Minimum order quantity: 50
Order in multiples of: 50
-
![[50 Pack] Simpson Strong-Tie THD37400CS Titen HD 3/8 in. x 4 in. Zinc-Plated Countersunk Head Heavy-Duty Screw Anchor](https://heyden.dreamhosters.com/wp-content/uploads/2022/12/b3d40e526ae041ff4ca2b4995a048052d426f671-3-600x600.jpg)
Delivery Estimate May 09 - May 13
$61.84
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Standard fractional sizes, hole size same as anchor size
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
- 6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
- Countersunk head allows screw anchor applications incompatible with a hex head
- Available in 1/4″ and 3/8″ diameters
-
Delivery Estimate May 09 - May 13
$95.38
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Out of stock
$629.50
Features
- 21 Gauge Steel Tie Wire
- Bare steel with no coating
- For use with MAX RB397, RB398, RB517 and RB518
-
$532.99
Features
- Breathable polyester mesh
- 2″ two-tone tape for optimum visibility
- Zipper closure
- 2 mic tabs with reinforced stitching
- 2 lower external flap pockets
-
$532.99
Features
- Solid front and mesh back for breathability
- 2″ two-tone tape for optimum visibility
- Zipper closure
- 2 mic tabs with reinforced stitching
- 2 lower external flap pockets
-
Delivery Estimate May 09 - May 13
$28.49
Features
- STB2-37334 has a chamfered top designed to prevent mushrooming during installation
- Qualified for static and seismic loading conditions (seismic design categories A through F)
- Suitable for horizontal, vertical and overhead applications
- Qualified for minimum concrete thickness of 3 1/4″, and lightweight concrete-over-steel deck thickness of 2 1/2″ and 3 1/4″
- Standard (ANSI) fractional sizes: fits standard fixtures and installs with common drill bit and tool sizes
-
Delivery Estimate May 09 - May 13
$235.69
Features
- Quick and easy installation
- 3PB is made of durable noncorrosive plastic
- No tools required
-
Delivery Estimate May 09 - May 13
$249.89
Features
- Quick and easy installation
- 3BB is made of durable noncorrosive plastic
- No tools required
-
Delivery Estimate May 09 - May 13
$242.39
Features
- Quick and easy installation
- 4-2IN-UBC is made of durable noncorrosive plastic
- Snaps over the rebar
-
Delivery Estimate May 09 - May 13
$45.58
Features
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading
-
Delivery Estimate May 09 - May 13
$17.29
Features
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading
-
SALE 6% OFF
Delivery Estimate May 09 - May 13
$106.92 Original price was: $106.92.$100.50Current price is: $100.50.
Features
- THD37600H is tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Standard fractional sizes
- Do not reuse anchor
-
![[50 Pack] Simpson Strong-Tie THDB25412CS Titen HD 1/4 in. x 4-1/2 in. Zinc-Plated Countersunk Head Heavy-Duty Screw Anchor](https://heyden.dreamhosters.com/wp-content/uploads/2022/12/b3d40e526ae041ff4ca2b4995a048052d426f671-2-600x600.jpg)
Delivery Estimate May 09 - May 13
$56.28
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Standard fractional sizes, hole size same as anchor size
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
- 6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
- Countersunk head allows screw anchor applications incompatible with a hex head
- Available in 1/4″ and 3/8″ diameters
-
Delivery Estimate May 09 - May 13
$179.09
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
![[50 Pack] Simpson Strong-Tie THD37212CS Titen HD 3/8 in. x 2-1/2 in. Zinc-Plated Countersunk Head Heavy-Duty Screw Anchor](https://heyden.dreamhosters.com/wp-content/uploads/2022/12/b3d40e526ae041ff4ca2b4995a048052d426f671-4-600x600.jpg)
Delivery Estimate May 09 - May 13
$62.17
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Standard fractional sizes, hole size same as anchor size
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
- 6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
- Countersunk head allows screw anchor applications incompatible with a hex head
- Available in 1/4″ and 3/8″ diameters
-
Delivery Estimate May 09 - May 13
$374.62
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
![[50 Pack] Simpson Strong-Tie THD37134H Titen HD 3/8 in. x 1-3/4 in. Heavy-Duty Screw Anchor](https://heyden.dreamhosters.com/wp-content/uploads/2022/12/A_THD62600H_ProdPho_Pho_Prod_TitenHD-Zinc_C0-4-600x600.jpg)
Delivery Estimate May 09 - May 13
$40.62
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Delivery Estimate May 09 - May 13
$53.42
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Standard fractional sizes, hole size same as anchor size
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
- 6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
- Countersunk head allows screw anchor applications incompatible with a hex head
- Available in 1/4″ and 3/8″ diameters
-
![[50 Pack] Simpson Strong-Tie THD37212H Titen HD 3/8 in. x 2-1/2 in. Heavy-Duty Screw Anchor](https://heyden.dreamhosters.com/wp-content/uploads/2022/12/A_THD62600H_ProdPho_Pho_Prod_TitenHD-Zinc_C0-6-600x600.jpg)
Delivery Estimate May 09 - May 13
$45.77
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Delivery Estimate May 09 - May 13
$188.46
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Delivery Estimate May 09 - May 13
$93.08
Features
- Thread design undercuts to efficiently transfer the load to the base material
- Serrated cutting teeth and thread design enable quick and easy installation
- Specialized heat-treating process creates tip hardness to facilitate cutting while the anchor body remains ductile
- Designed to install using a rotary hammer or hammer drill with standard ANSI drill bits — no special tools required
- Installs with standard-sized sockets
- Code listed for cracked and uncracked concrete applications under the 2015, 2012 and 2009 IBC/IRC, per ICC-ES ESR-2713
- FM listed
-
Delivery Estimate May 09 - May 13
$316.92
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Delivery Estimate May 09 - May 13
$346.15
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
![[50 Pack] Simpson Strong-Tie THDC25300H6SS Titen HD 1/4 in. x 3 in. Type 316 Stainless-Steel Heavy-Duty Screw Anchor](https://heyden.dreamhosters.com/wp-content/uploads/2022/12/fe7beccebff488653396b015a2d93bdb19169a58-1-600x600.jpg)
Delivery Estimate May 09 - May 13
$190.14
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Delivery Estimate May 09 - May 13
$288.46
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
![[50 Pack] Simpson Strong-Tie THD37500HMG Titen HD 3/8 in. x 5 in. Mechanically Galvanized Heavy-Duty Screw Anchor](https://heyden.dreamhosters.com/wp-content/uploads/2022/12/THD50500H1500_300-600x600.jpg)
Delivery Estimate May 09 - May 13
$166.15
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Delivery Estimate May 09 - May 13
$223.08
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Delivery Estimate May 09 - May 13
$59.69
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
SALE 20% OFF
Delivery Estimate May 09 - May 13
$183.25 Original price was: $183.25.$146.60Current price is: $146.60.
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Delivery Estimate May 09 - May 13
$72.26
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Standard fractional sizes, hole size same as anchor size
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
- 6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
- Countersunk head allows screw anchor applications incompatible with a hex head
- Available in 1/4″ and 3/8″ diameters
-
Delivery Estimate May 09 - May 13
$62.38
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
SALE 6% OFF
Delivery Estimate May 12 - May 14
$64.92 Original price was: $64.92.$61.02Current price is: $61.02.
Features
- Thread design undercuts to efficiently transfer the load to the base material
- Serrated cutting teeth and thread design enable quick and easy installation
- Specialized heat-treating process creates tip hardness to facilitate cutting while the anchor body remains ductile
- Designed to install using a rotary hammer or hammer drill with standard ANSI drill bits — no special tools required
- Installs with standard-sized sockets
- Code listed for cracked and uncracked concrete applications under the 2015, 2012 and 2009 IBC/IRC, per ICC-ES ESR-2713
- FM listed
-
Delivery Estimate May 09 - May 13
$42.54
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Delivery Estimate May 09 - May 13
$288.46
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Delivery Estimate May 09 - May 13
$45.08
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Delivery Estimate May 09 - May 13
$72.85
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Delivery Estimate May 09 - May 13
$90.00
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
![[50 Rolls] TW898 S Max 21ga Stainless Steel Tie Wire for MAX RB398 series](https://heyden.dreamhosters.com/wp-content/uploads/2021/03/TW898-EG-1-scaled-1-600x600.jpg)
$879.40
TW898 S Max 21ga Stainless Steel Tie Wire for MAX RB398 series
![Century Glove 130-100GM
100% Cotton Dress Glove with Raised Stitching on Back - Open Cuff [1 dozen]](https://heyden.dreamhosters.com/wp-content/uploads/2023/02/130-100GM-UP-600x600.jpg)
Century Glove 130-100GM
100% Cotton Dress Glove with Raised Stitching on Back - Open Cuff [1 dozen] 
