“BFB48 Marshalltown Broom Float” has been added to your cart.
View cart
“BFB36 Marshalltown Broom float” has been added to your cart.
View cart
“West Chester 1027OR PVC
Dipped Glove with Insulated Foam Liner and Smooth Finish – 12″ Length [1
dozen]” has been added to your cart.
View cart
“Simpson Strong-Tie CS16 CS 150 ft.
16-Gauge Galvanized Coiled Strap” has been added to your cart.
View cart
Showing 41–80 of 97 resultsSorted by popularity
-

$2.29
Features:
- An indented embedment line ensures accurate embedment depth
- Compatible with the Simpson Strong-Tie preassembled TSS snap-in seat
- Load rated for wind and seismic forces
- 12-in. exposed length
- Embed 4 in. into a poured concrete bond beam or grouted block wall
-


$13.49
Features:
- Suitable for retrofit applications
- The embossments add stiffness in crucial areas for improved performance
- Simple to install and can be installed on the inside or outside of the wall
- Load rated to resist high-wind forces
- 2-ply
-


$53.96
Features:
- Attaches a post to existing concrete for decks, patio covers and other top-supported structures
- Features 1-in. standoff to help prevent rot at post end
- Slotted for adjustability
- Designed for versatility, cost-effectiveness and maximum uplift performance
- Nominal post size: 6×6
-


$2.41
Features:
- Patented double-shear nailing design provides greater strength with fewer nails
- Speed prongs for fast and easy installation
- Angled joist nailing easier in tight spaces
- Do not bend or remove tabs
- Nominal joist size: 2×10, 2×12, 2×14
-


$5.29
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 5/8 in.
- Length: 10 in.
- Made from zinc-plated carbon steel
-


$4.42
Features:
- Patented double-shear nailing design provides greater strength with fewer nails
- Speed prongs for fast and easy installation
- Angled joist nailing easier in tight spaces
- Do not bend or remove tabs
- Nominal joist size: Double 2×10 and Double 2×12
-


$30.43
Features:
- Provides a positive connection for a post to a wood deck
- Stronger than angled nailing or screw fastening
- Reduces the chance of the post splitting and eliminates nailing into end grain
- Not recommended for non top-supported installations (such as fences or unbraced carports)
- Nominal post size: 6x
-


$8.12
Features:
- Patented double-shear nailing design provides greater strength with fewer nails
- Speed prongs for fast and easy installation
- Angled joist nailing easier in tight spaces
- Do not bend or remove tabs
- Nominal joist size: Triple 2×8 and Triple 2×10
-


$3.37
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 3/4 in.
- Length: 6-1/4 in.
- Made from zinc-plated carbon steel
-

$35.93
Features:
- SDS-plus shank power setting tool for DIAB anchors
- For use with Simpson Strong-Tie Drop-In models DIAB50, DIABL50, and DIAB50C
- Sets drop-ins for overhead applications
- Drop-in anchors are sold separately
- Made from carbon steel
-

$0.74
Features:
- MP24 is versatile and easy-to-use mending plate for wood-to-wood connections
- These non-structural connectors are ideal for general fix-up work
- Installs without nails; align wood with arrows at joint and hammer plate to embed prongs
- Used for non-structural applications only (not for truss applications)
- Width: 2 in.
-


$0.96
Features:
- Bolt diameter: 3/8 in.
- Dimensions: 2 in. x 2 in.
- Made from 3/16 in. steel
- Uncoated steel construction
-


$2.24
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-


$53.96
Features:
- Extra optional triangle holes for additional load
- HUC-series hangers are tested, load rated and code compliant
- Install wood joists to wood, masonry and concrete
- Seat width: 4-11/16 in.
- Nominal joist size: Triple 2×10
-


$46.82
Features:
- Attaches a post to existing concrete for decks, patio covers and other top-supported structures
- Features 1-in. standoff to help prevent rot at post end
- Slotted for adjustability
- Designed for versatility, cost-effectiveness and maximum uplift performance
- Nominal post size: 4×6
-

$26.71
Features:
- The nailing pattern allows for nailing to the edges of double 2x’s
- Strap nail slots are countersunk to provide a lower nail head profile
- The slots below the embedment line enable increased front-to-back concrete bond and help to reduce spalling
- Standard strap length: 26-1/8 in.
- Made from 12-gauge steel
-


$210.59
Features:
- Sized to fit nominal 2x lumber
- Packaged in lightweight cartons
- Length: 150 ft.
- Made from 16-gauge steel
- Galvanized (G90) for extra corrosion resistance
-


$5.31
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-


$18.35
Features:
- Provides a positive connection for a post to a wood deck
- Stronger than angled nailing or screw fastening
- Reduces the chance of the post splitting and eliminates nailing into end grain
- Not recommended for non top-supported installations (such as fences or unbraced carports)
- Nominal post size: 6x
-


$603.93
Features:
- Semi-automatic and fast cycling
- PT-27 is Compatible with Simpson Strong-Tie powder loads and pins
- Fastener length: 1/2? 2-1/2 in. (3 in. washered)
- Fastener type: .300 in. or 8 mm-headed fasteners or 1/4-in.-20 threaded studs
- Load caliber: 0.27 strip loads, brown through red (levels 2?5)
-


$4.20
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-


$20.24
Features:
- SUL = skewed left
- Can accommodate joists skewed 40 to 50 degrees
- Angled nail slots direct nails for proper installation
- Nominal joist size: 2×10 or 2×12
- Made from 16-gauge steel
-

$16.04
Features:
- The minimum effective shank length must equal or exceed the sum of the thickness of the attached material and the minimum embedment depth
- Code listed per ICC-ES ESR-2138, Florida FL15730 and LA RR25469
- Compatible with Simpson Strong-Tie powder-actuated tool systems as well as other common tools
- .300-in. head diameter / .157-in. shank diameter
- 1-in. washer
-


$20.24
Features:
- SUR = skewed right
- Features obround nail holes on the acute side, allowing nails to be easily installed parallel to the joist
- These hangers cannot be modified but will accommodate a 40 degree to 50 degree skewed joist
- Available with the acute flange turned in to accommodate end-of-wall installation for solid sawn sizes only (SURC or SULC)
- Nominal joist size: 2×10 or 2×12
-


$3.05
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-


$5.59
Features:
- Can be installed filling round holes only, or filling round and triangle holes for maximum values
- Nominal joist size: 2×6
- Made from 16-gauge steel
- Galvanized (G90) for extra corrosion resistance
-


$2.66
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 3/4 in.
- Length: 4-1/4 in.
- Made from zinc-plated carbon steel
-


$10.71
Features:
- Attaches a post to existing concrete for decks, patio covers and other top-supported structures
- Features 1-in. standoff to help prevent rot at post end
- Slotted for adjustability
- Designed for versatility, cost-effectiveness and maximum uplift performance
- Nominal post size: 4×4
-


$51.97
Features:
- CDT10S Manual dispensing tool
- Features a steel carriage for ultimate durability and is engineered for continuous, high-volume use
- Double-gripping plates that help extend tool life
- For SET3G10 adhesive and other 10 oz. single-cartridge adhesives
-

$26.20
Features:
- Discontinued
- Designed for nail- or bolt-on applications
- For use in vertical or horizontal applications
- 5/16 in. seat thickness
- Length: 19-3/4 in.
- Made from 12-gauge steel
-


$28.56
Features:
- Attaches a post to existing concrete for decks, patio covers and other top-supported structures
- Features 1-in. standoff to help prevent rot at post end
- Slotted for adjustability
- Designed for versatility, cost-effectiveness and maximum uplift performance
- Nominal post size: 6×6
-


$6.68
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 5/8 in.
- Length: 8-1/2 in.
- Made from mechanically galvanized carbon steel
-

$52.89
This item has been DISCONTINUED.
-

$1.29
Features:
- A versatile and easy-to-use mending plate for wood-to-wood connections
- These non-structural connectors are ideal for general fix-up work
- Installs without nails; align wood with arrows at joint and hammer plate to embed prongs
- Used for non-structural applications only (not for truss applications)
- Width: 3 in.
-


$9.51
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 5/8 in.
- Length: 10 in.
- Made from mechanically galvanized carbon steel
-

$1.72
Features:
- An indented embedment line ensures accurate embedment depth
- Compatible with the Simpson Strong-Tie preassembled TSS snap-in seat
- Load rated for wind and seismic forces
- 8-in. exposed length
- Embed 4 in. into a poured concrete bond beam or grouted block wall
-


$5.54
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-

$2.83
Features:
- Helps resist tension forces
- Staggered nail pattern reduces the potential for splitting
- Width: 1-1/4 in.
- Length: 21-5/8 in.
- Made from 16-gauge steel
-


$266.58
Features:
- Cap-style head countersinks fully into the double top plate to avoid interference with drywall or finish trades
- Wide tolerance on installation angle makes it easy to install the SDWC correctly
- Can be installed from inside the structure, eliminating exterior work on the upper stories and enhancing job safety
- Fastening can be performed before or after exterior sheathing is applied for added flexibility
- Type-17 point for faster starts and easier driving
-


$2.59
Features:
- Available with the bend reversed; specify –REV- after the model number, such as HTS16-REV
- Versatile with many lengths offered to fit the specific application
- Straps do not need to be wrapped over the truss to achieve the allowable load
- Length: 16 in.
- Made from 14-gauge steel