“[50 Pack] Simpson Strong-Tie THDB25412CS Titen HD 1/4 in. x 4-1/2 in. Zinc-Plated Countersunk Head Heavy-Duty Screw Anchor” has been added to your cart.
View cart
Showing 361–400 of 930 resultsSorted by popularity
SALE 6% OFF
$ 328.99 Original price was: $328.99. $ 309.25Current price is: $309.25.
Features
Makita-built motor delivers 1,100 lbs. of dispensing force to dispense the highest viscosity adhesives and sealants
5 speed dial optimizes flow rate from 0-66 IPM
Variable speed trigger allows user to match speed to the application
360° rotatable cartridge holder fits 10 oz. and 300 ml cartridges
Drip-reduction feature automatically relieves pressure on the material when trigger is released to prevent unintentional dispensing
$ 378.99
Features
Makita-built motor delivers 1,100 lbs. of dispensing force to dispense the highest viscosity adhesives and sealants
5-speed dial optimizes flow rate from 0-66 IPM
Variable speed trigger allows user to match speed to the application
360° rotatable cartridge holder fits 20 oz. cartridges, sausage packs and bulk caulk and adhesives
Includes 3 pistons for use with cartridges, sausage packs and bulk materials
$ 287.50
Features
Makita-built motor delivers 1,100 lbs. of dispensing force to dispense the highest viscosity adhesives and sealants
5 setting speed dial optimizes flow rate from 0-66 IPM
Variable speed trigger allows user to match the speed to the application
360° rotatable cartridge holder fits 28-29 oz. cartridges
Drip-reduction feature automatically relieves pressure on the material when trigger is released to prevent unintentional dispensing
$ 12.27
Features
Opposing flanges provide increased lateral resistance
Attains full allowable load using either common nail or pneumatic nail sizes
Light-gauge material designed for light-duty applications
$ 41.19
Features
FB24Z preinstallation of brackets allows rails to slide into place easily
Eliminates need for toe nails or screws
Wood Connector Resources
$ 107.39
Features
Certified welds for confidence in strength and loading
Uplift loads increased for earthquake or wind loading
Bolt spacing that meets NDS code requirements to ensure optimal performance
Diamond holes to provide temporary fastening
$ 20.99
The BC post cap is designed to connect a beam to a post. The 18-gauge material of this post cap makes it ideal for light-duty connections. The BC provides uplift and lateral resistance and includes sizes for both nominal and rough lumber.
SALE 6% OFF
$ 106.92 Original price was: $106.92. $ 100.50Current price is: $100.50.
Features
THD37600H is tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes
Do not reuse anchor
$ 80.00
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 195.69
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 68.78
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 68.00
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 138.54
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 182.46
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 50.40
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 87.26
Features
Tested in accordance with ACI 355.2 and AC193
Qualified for static, wind and seismic loading conditions
Available in 1/2″ and 5/8″ diameters
Standard fractional sizes — the hole size matches the anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
For added convenience, a 1/2″ socket adapter and (2) T-drive bits are included in each box
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
Washer head allows screw anchor applications incompatible with a hex head
$ 106.62
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 47.92
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 43.19
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 120.00
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 158.45
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes, hole size same as anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
Countersunk head allows screw anchor applications incompatible with a hex head
Available in 1/4″ and 3/8″ diameters
$ 115.52
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes, hole size same as anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
Countersunk head allows screw anchor applications incompatible with a hex head
Available in 1/4″ and 3/8″ diameters
$ 63.69
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 140.62
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 128.54
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 151.23
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 27.69
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 92.62
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 17.52
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 56.28
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes, hole size same as anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
Countersunk head allows screw anchor applications incompatible with a hex head
Available in 1/4″ and 3/8″ diameters
$ 63.19
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 36.78
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 46.52
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 179.09
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 144.49
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 160.00
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 62.17
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes, hole size same as anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
Countersunk head allows screw anchor applications incompatible with a hex head
Available in 1/4″ and 3/8″ diameters
$ 374.62
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 114.77
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended