“[20 Pack] Simpson Strong-Tie THD50612H4SS Titen HD 1/2 in. x 6-1/2 in. Type 304 Stainless Steel Heavy-Duty Screw Anchor” has been added to your cart.
View cart
Showing 1–40 of 142 resultsSorted by popularity
$ 0.43
Features:
Faster installation than previous drop-in anchor design sets with 40% fewer hammer hits
Positive-set marking system indicates when anchor is properly set
Zinc-plated carbon steel
Length: 2 in.
Drill bit diameter: 5/8 in.
Minimum order quantity: 50
Order in multiples of: 50
$ 15.18
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 29.95
Features
PFM1411020 is designed for standard ANSI tolerance drill bits
Patented thread design offers low installation torque
Tough threads for tapping high strength concrete
Ratchet teeth on underside of hex washer head lock against the fixture
Can be installed closer to the edge than traditional expansion anchors
$ 5.53
Features:
Chamfered top designed to prevent mushrooming during installation
Qualified for static and seismic loading conditions (seismic design categories A through F)
Suitable for horizontal, vertical and overhead applications
Qualified for minimum concrete thickness of 3-1/4 in., and lightweight concrete-over-steel deck thickness of 2-1/2 in. and 3-1/4 in.
Tested per ACI355.2 and AC193
$ 39.46
Features
PFM1411380 is designed for standard ANSI tolerance drill bits
Patented thread design offers low installation torque
Tough threads for tapping high strength concrete
Ratchet teeth on underside of hex washer head lock against the fixture
Can be installed closer to the edge than traditional expansion anchors
$ 39.90
Features
PFM1411100 is designed for standard ANSI tolerance drill bits
Patented thread design offers low installation torque
Tough threads for tapping high strength concrete
Ratchet teeth on underside of hex washer head lock against the fixture
Can be installed closer to the edge than traditional expansion anchors
$ 87.26
Features
Tested in accordance with ACI 355.2 and AC193
Qualified for static, wind and seismic loading conditions
Available in 1/2″ and 5/8″ diameters
Standard fractional sizes — the hole size matches the anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
For added convenience, a 1/2″ socket adapter and (2) T-drive bits are included in each box
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
Washer head allows screw anchor applications incompatible with a hex head
$ 4.95
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 92.31
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 28.95
Features
PFM1411060 is designed for standard ANSI tolerance drill bits
Patented thread design offers low installation torque
Tough threads for tapping high strength concrete
Ratchet teeth on underside of hex washer head lock against the fixture
Can be installed closer to the edge than traditional expansion anchors
$ 49.43
Features
Tested in accordance with ACI 355.2 and AC193
Qualified for static, wind and seismic loading conditions
Available in 1/2″ and 5/8″ diameters
Standard fractional sizes — the hole size matches the anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
For added convenience, a 1/2″ socket adapter and (2) T-drive bits are included in each box
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
Washer head allows screw anchor applications incompatible with a hex head
$ 95.38
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
SALE 6% OFF
$ 106.92 Original price was: $106.92. $ 100.50Current price is: $100.50.
Features
THD37600H is tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes
Do not reuse anchor
$ 80.00
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 195.69
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 68.78
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 68.00
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 138.54
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 182.46
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 50.40
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 87.26
Features
Tested in accordance with ACI 355.2 and AC193
Qualified for static, wind and seismic loading conditions
Available in 1/2″ and 5/8″ diameters
Standard fractional sizes — the hole size matches the anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
For added convenience, a 1/2″ socket adapter and (2) T-drive bits are included in each box
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
Washer head allows screw anchor applications incompatible with a hex head
$ 106.62
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 47.92
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 43.19
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 120.00
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 158.45
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes, hole size same as anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
Countersunk head allows screw anchor applications incompatible with a hex head
Available in 1/4″ and 3/8″ diameters
$ 115.52
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes, hole size same as anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
Countersunk head allows screw anchor applications incompatible with a hex head
Available in 1/4″ and 3/8″ diameters
$ 63.69
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 140.62
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 128.54
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 151.23
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 27.69
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 92.62
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 17.52
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 56.28
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Standard fractional sizes, hole size same as anchor size
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
Countersunk head allows screw anchor applications incompatible with a hex head
Available in 1/4″ and 3/8″ diameters
$ 63.19
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 36.78
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 46.52
Features
Tested in accordance with ACI 355.2, AC193 and AC106
Qualified for static, wind and seismic loading conditions
Thread design undercuts to efficiently transfer the load to the base material
Standard fractional sizes
Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
Reuse of the anchor will not achieve listed loads and is not recommended
$ 179.09
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106
$ 144.49
Features
THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
Ideal for exterior or corrosive environments
Less carbon steel, less expansion
Installs with an impact wrench or by hand tool
Tested in accordance with ACI355.2, AC193 and AC106